A range of injection moulded plastic parts for 16mm scale.
BOGIES (pair) for 32mm gauge
These require 24mm wheelsets and bearings
NB1 L & B® 4'wb Wagon £4.35
NB2 L & B® 3'wb Wagon £4.35
NB3 "Fox" 3'wb Wagon £4.90
NB4 L & B® 4'4"wb Coach £6.15
AXLEGUARDS (four)
NA1 "Talyllyn" Wagon £1.85
NA2 "Record" Wagon £1.20
NA8 "W & L" Wagon £2.35
NA22 "Sandy River"
Auto (inside sprung) £2.80
Set of four based on those fitted to the Sandy River (US) railcars converted
from road vehicles.
See NA20 for radiator.
NA26 Simplex
Loco £2.35
Set of four as fitted to Simplex 8/12h.p. locos. Includes bracket for skid bar.
Could also be used for small wagons
BRAKEGEAR
NA9 "W & L" B/shoes (4) for 24-30mm wheels £1.35
NA10 "GVT" Coach (pair) for 5’6” wd and 1’10” wheels £2.10
WHEELS (four without axles 2mm req)
NW1 15mm 4-hole Disc as used on skip wagons £1.50
NW2 15mm 6-hole Disc as used on skip wagons £1.50
NW3 24mm Curly Spoke as used on slate wagons £1.85
NW4 20mm Five Spoke £1.60
NW9 30mm Eight Spoke £2.35
CA11 10 x 75mm long, 2mm dia. Axles 80p
LOCO WHEELS (without axles)
NW6 "Faller" 6 x 21mm for 2mm axles £3.00
NW7 "Excelsior" (0-4-2) £2.35
FITTINGS
NA3 Coach Doorhandles £1.60
NA4 Hooks & Eyes £1.60
NA5 Nut & Bolt Heads £1.35
NA6 Brake Handwheels £1.35
NA7 Rivet Heads £1.35
NA11 Centre Buffer (pair) £2.35
NA12 Coach/wagon Sprung Buffers (4) £3.00
NA13 Handrail Knobs(12) £1.35
NA14 Loco Headlight £1.85
NA15 Coach Door Vents (4) £1.00
NA16 Simplex type Radiator Front £1.00
Two are required for free standing rad.
NA17 Louvres (3 sizes) for detailing locos etc. £1.35
NA20 Ford 'A' Type £1.00
Use on railbuses e.g. Irish or Sandy River
NA21 Detailing parts for
Simplex Locos £3.35
Brake Wheel & Handle plus supporting frame, sandboxes, chequer plate for
driver's footplate, gearbox end detail,
starter handle guide, clutch pedal and support bracket for silence.
(some parts based on Rye & Camber "Kent Construction/Hibberd" loco)
NA23 Radiator Panel 90p
Flat panel for locos or larger railcars. 48mm high x 29mm wide.
NA24 Diesel Horns £1.00
One each of 20mm long & 25mm long (supplied as "halves")
NA25 Pressed-type Loco Seat
£1.10
As used on small diesel locos. 20mm wide x 19mm deep.
SIGNAL PARTS
NS1 Signal Ladder (approx. 200mm) £1.35
NS2 Signal Parts: arm, lamp/bracket, finial, lever, etc. £3.90
NS3 2 Brackets for junction signals etc. £1.50
FIGURES
NF1 Standing Male £2.10
NF3 Seated Male £3.00
Speed Controllers for Battery Locomotives
Electronic Speed Controls: (assembled & tested)
TYPE 1:
for 3 volt motors. PP3 type connector for 2 AA holderand wiring diagram. Size 35mm x 25mm x 18mm approx. Assembled - £9.95
TYPE 2:
for 4.5 - 12 volt motors, max current 1200ma
(such as supplied by "domestic" rechargeable C cells) Size 40mm x 35mm x 22mm approx.
Assembled - £10.55
TYPE 3:
for 12volt "gel" cells (e.g. Yuasa). Max current 1200ma.Assembled - £11.15
TYPE 4:
for 12volt "gel" cells (e.g. Yuasa). Max. current 3A. Assembled - £12.20
Last updated 28/2/06